A. Fillinger Inc. Identifies Misuse of Nails, Screws

Oct. 25, 2011

They’re the simplest fasteners in the workshop, but nails and screws are not always used correctly.  A. Fillinger Inc., a fourth generation family business, ACE Hardware store, and custom cabinetry and millwork company, offers tips for properly selecting and using them.

 

“You wouldn’t think nails and screws would be complicated,” said Ryan Fillinger, vice president of marketing and sales.  “But if you’ve visited our store, you know there are many types and sizes. Make sure you’re using the right one for the job.”

 

**Choosing the Nail

 

Four nail types handle most fastening jobs – common, casing, finishing, and brads.

 

* Choose a common nail, the most widely used, when the appearance of the flat nail head is not objectionable.

* Choose a casing nail (slightly heavier than a finishing nail) primarily for cabinet work or interior trim. Normally countersunk, the head should be covered with putty or wood filler. Casing nails are good for 3/4-inch plywood.

* Used for finishing work, a finish nail has a rounded head that can be driven flush with the surface of the wood and may or may not be countersunk.

* Thinner, shorter, and smaller than finish nails, brads are for light assembly work where the head should be concealed, best in plywood no thicker than 1/4 inch.

 

Nails are normally driven through a thinner piece of wood and into a thicker one. A rule of thumb for length is that the nail should always be about three times as long as the thickness of the thinner piece, allowing 2/3 of the nail to provide holding power in the thick piece.

 

**Using the Nail

 

Using the wrong kind of nail is the biggest mistake. Another is to drive two nails into the same grain near the end of a plank. Still another mistake is to try to countersink a nail without a nail set. To countersink properly, drive the casing or finish nail into the wood, leaving the head slightly above the surface. Use a nail set that is the same size as the head and use it to drive the nail in slightly below the surface. Fill the recessed area with wood putty or filler, and sand it flush once it’s dry.

 

“There are some projects that will cause you headaches unless you use specialty nails,” Fillinger said. Specialty nails are available for:

 

* Wallboard

* Holding wood to concrete or masonry

* Corners (corrugated fasteners)

* Upholstery

 

**Choosing the Screw

 

There are two types of screws – slot-head (one slot requiring a slotted screwdriver) and Phillips-head (a cross slot requiring a Phillips screwdriver). The heads are available in either flat (flush with the surface), round (protrudes in a half-circle), or oval (extends above the surface in a slight oval).

 

The thicker the plywood, the bigger and longer the screw. “For 1/4-inch plywood, we recommend No. 4, 3/4-inch long screws. For 3/4-inch plywood, you’re looking at a No. 8 screw with a 1-1/2-inch length.”

 

**Using the Screw

 

Screws, especially Phillips-head, can become stripped if used improperly. “It sounds basic, but using the wrong screwdriver is a common error,” Fillinger said. Stripping often occurs when the bit in an electric drill is too small for the screw.

 

Another mistake is attempting to use a screw without first making a pilot hole. When the two pieces of wood are held securely, drill a pilot hole through the top piece into the second piece. The hole should be slightly smaller in diameter and as long as the screw.

 

For countersinking, use the pilot hole as a guide and drill a hole slightly larger than the screw shank through the top piece. Use a countersink to drill for countersinking oval or flathead screws. To completely conceal the head of the screw, a dowel plug can be used.

 

“It can get frustrating when you need to insert a screw in an area that’s hard to reach,” Fillinger said. “Get yourself a ratchet or offset screwdriver for this. You won’t regret it.”

 

Established in southeastern Wisconsin in 1938, A. Fillinger Inc. was one of the early ACE Hardware affiliates and has more than 20,000 products on-hand. The millwork division specializes in custom cabinetry and mouldings. A. Fillinger is located at 6750 N. 43rd St. in Milwaukee.

 

The complete guide to screws and nails, provided by ACE Hardware, is available at www.acehardware.com. A. Fillinger can be reached at 414-353-8433 and online at www.afillinger.com.

Community Watch

» Initial Reaction Podcast: Menomonee Falls baseball virtuoso Ty Weber and Big Ten Media Day Updated:  7/29

» Germantown 'craft winery' owner crafts 9,000 bottles by hand 7/27

» Menomonee Falls Girl Scout aids in Central America's conservation efforts 7/26

» Two suspects apprehended in Menomonee Falls armed robbery Updated:  7/26

» Menomonee Falls claims baseball title as team 7/26

» Major phase in Menomonee Falls' White Stone Station completed 7/25

» Putting in the effort: Menomonee Falls baseball team wins second state title 7/25

» Roble pitches Menomonee Falls baseball team into state title game 7/25

» Menomonee Falls man pleads guilty to homicide after killing bicyclist Updated:  7/25

» Behind marvelous day by Ty Weber, Menomonee Falls baseball repeats as state champion 7/22

» Live coverage: 2016 WIAA State Summer Baseball Tournament Updated:  7/22

» Roble pitches Menomonee Falls baseball team into state final, 6-0 7/22

» Falls woman dreams of starting her own dessert bus 7/21

» Social media story on the storms rolling through Milwaukee area 7/21

» Donges Bay Road reconstruction enters final phase 7/21

» Wanakia Wildlife gives a bird's-eye view to Menomonee Falls Nature Camp kids 7/21

» Resources available to Waukesha County residents during extreme heat 7/21

» Southbound Highway 145 to close for construction in Germantown 7/20

» Initial Reaction Podcast: Wisconsin Badgers football, WIFCA All-Star game 7/20

» Menomonee Falls woman arrested for OWI after running over her fiancé Updated:  7/19

» GMC set to dominate state summer baseball tournament 7/19

» 'Two more wins': Menomonee Falls baseball team heads back to state 7/19

» Menomonee Falls baseball team heads back to state with upset of West 7/18

» Taste of Germantown event to raise funds for pavilion 7/18

» Old Falls Village brings Civil War to life 7/18

View All Posts Got a tip? Welcome rss

Waukesha County Fair

 

The 2016 Waukesha County Fair saw rain, scorching temps and tropical humidity throughout its five-day run. Check out our stories, photos and video from the fair, including coverage of the new pig, duck and goat races, the 50th annual Fairest of the Fair contest, as well as a ranking of the top food items.

Best Summer Ever

 

We've made it easy for you to get out and go this summer. From hitting the trails for a bike ride or walk, to where to find beer gardens in the area, to the best places to swim in Waukesha County to the best summer drinks and summer reads, check out our 2016 summer guide.

Advertisement

Advertisement

CONNECT    

Advertisement

Most Popular